|
#629564
Sun Sep 13 2015 04:18 PM
|
Joined: Aug 2015
Posts: 35
Active Member
|
OP
Active Member
Joined: Aug 2015
Posts: 35 |
I've been working on this 966 and I can't seem to figure out how the light fixture should be pointing. The conduit with the 90 degree bend came with the pump when I acquired it. If I point it down as it was when I disassembled it there is no room for a 'standard' light bulb and it would hang down into the porcelain face plate area. If I point it up it conflicts with the top of the pump. Did these pumps use a special light bulb, and/or can someone point me to the direction the fixture should be pointing. Thanks
Last edited by ed1966ss; Sun Sep 13 2015 04:19 PM.
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Nov 2002
Posts: 4,962 Likes: 17
Moderator
|
Moderator
Joined: Nov 2002
Posts: 4,962 Likes: 17 |
FREEDOM oil items wanted.
|
|
|
|
Joined: Nov 2000
Posts: 7,791 Likes: 9
Veteran Member
|
Veteran Member
Joined: Nov 2000
Posts: 7,791 Likes: 9 |
http://petrolianacollectibles.com/bennett%20956.htmParts catalog shows every part of the 966 and where it goes. Jack Sim
Author, 1st & 2nd editions of Gas Pump ID book, 3rd edition is now available at www.gaspumpbible.comAir Meter ID book also available
|
|
|
|
Joined: Aug 2015
Posts: 35
Active Member
|
OP
Active Member
Joined: Aug 2015
Posts: 35 |
Thanks, So it looks like the bulb would sit just below the sight glass in that configuration. I'll look at it closer tomorrow. Thanks again. I need to pick up one of the parts lists.
|
|
|
|
Joined: Feb 2014
Posts: 2,995 Likes: 109
Veteran Member
|
Veteran Member
Joined: Feb 2014
Posts: 2,995 Likes: 109 |
Ed, The 90 degree elbow should be at about a 45 degree angle (if that makes sense). I went out to my garage and took these pictures for you. Hope this helps. -Steve
966
966 w bulb
966 side by side at eye level
Last edited by Speedracer; Sun Sep 13 2015 11:29 PM.
-Steve B. (WTB: 48" Flying A button, 48" black/org Phillips 66, White Star, and Chevrolet Signs. Also looking for a Wayne 866. Send a PM. Thanks.)
|
|
|
|
Joined: Aug 2015
Posts: 35
Active Member
|
OP
Active Member
Joined: Aug 2015
Posts: 35 |
Thanks Steve, That's perfect. Those 966's are cool.
I have most of the inside of my Bennett restored and need to get to work on the sides and doors. I'm looking to make mine visually working. I have it mostly figured out. I'll post some pic's soon. Ed
|
|
|
|
Joined: Feb 2014
Posts: 2,995 Likes: 109
Veteran Member
|
Veteran Member
Joined: Feb 2014
Posts: 2,995 Likes: 109 |
Cool let's see 'em when they're done.
-Steve B. (WTB: 48" Flying A button, 48" black/org Phillips 66, White Star, and Chevrolet Signs. Also looking for a Wayne 866. Send a PM. Thanks.)
|
|
|
|
|
|