|
#685913
Mon May 01 2017 07:05 PM
|
Joined: Aug 2009
Posts: 151
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Aug 2009
Posts: 151 |
Getting ready to wire and light my globes. In my last house I just wired each with a seperate plug and then took 5 plugs to a power strip. Now in the new place I want to wire 11 globes to a single recepticle, maybe with a motion activator so when I walk into the garage.... lights! Going to use 40 w equivelent led's so low amp pull and low heat. I have searched the forum for some old posts where those smarter than me showed how they wired, but to no avail. Anybody have that info available? Thanks in advance!
PS -Kevin, will get a pic up of my wayne 615 shortly.....
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Sep 2007
Posts: 19,379 Likes: 984
Veteran Member
|
Veteran Member
Joined: Sep 2007
Posts: 19,379 Likes: 984 |
wire in series .. ...
RANDY
|
|
|
|
Joined: Dec 2011
Posts: 8,818 Likes: 2
Veteran Member
|
Veteran Member
Joined: Dec 2011
Posts: 8,818 Likes: 2 |
I would personally wire them in a parallel circuit. That way if one bulbs burns out it won't cause the other bulbs to go out.
Dave GILL, Dave's Garage & Memorabilia, Inc.
|
|
|
|
Joined: Jan 2012
Posts: 1,338 Likes: 57
Veteran Member
|
Veteran Member
Joined: Jan 2012
Posts: 1,338 Likes: 57 |
I've never done this but I could see trying under-cabinetry lights (they are LEDS, dimmable, shaped like round pucks). They come grouped in threes or fours so you really wouldnt need to do anything different than your first approach, basicly no actual wiring. Last time I installed those in a kitchen was like 10 years ago, bet they are even better/cheaper now, maybe too much like a spot light? Like this: http://www.lampsplus.com/products/under-...q2S0aAg1K8P8HAQ
Last edited by Paul Bell; Mon May 01 2017 11:53 PM.
|
|
|
|
Joined: Dec 2012
Posts: 391 Likes: 31
Petro Enthusiast
|
Petro Enthusiast
Joined: Dec 2012
Posts: 391 Likes: 31 |
I would personally wire them in a parallel circuit. That way if one bulbs burns out it won't cause the other bulbs to go out. I'm with Dave on this one, not any more difficult than series to wire.
Randy
|
|
|
|
Joined: Jul 2000
Posts: 8,509 Likes: 289
Moderator
|
Moderator
Joined: Jul 2000
Posts: 8,509 Likes: 289 |
Here is a very basic drawing of lamps wired in parallel. Click on the picture to see more info. Here is a link to how I set up my globe shelves: http://www.oldgas.com/forum/ubbthreads.php?ubb=showflat&Number=599180
Jim "Oldgas" Potts Your host and moderator
|
|
|
|
Joined: Dec 2011
Posts: 8,818 Likes: 2
Veteran Member
|
Veteran Member
Joined: Dec 2011
Posts: 8,818 Likes: 2 |
Just to expand a little on the AC wiring. In AC circuits the black wire is the hot lead and should be wired to the center terminal of the lamp socket that the tip of the light bulb contacts. The white wire is the neutral lead and the threaded portion of the lamp socket is connected to the white lead. If a person were to accidentally touche the thread portion of the bulb while installing or removing it, they won't get zapped. If you are going to run a three prong plug the green wire is the ground lead and you can ground the globe holders.
Last edited by Dave's Garage; Wed May 03 2017 12:10 AM.
Dave GILL, Dave's Garage & Memorabilia, Inc.
|
|
|
|
Joined: Aug 2009
Posts: 151
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Aug 2009
Posts: 151 |
Great stuff, will post a photo when completed, Thanks!
|
|
|
|
|
|