|
#49276
Sat Feb 17 2007 07:03 PM
|
Joined: Jan 2005
Posts: 2,702
Veteran Member
|
OP
Veteran Member
Joined: Jan 2005
Posts: 2,702 |
Okay I give up !
I bought RG101 from Webers for my Wayne 70... I'm trying to do the ad glasses right now. I honestly don't see how this is ever going to fit inside the bezels. I can tell right from the start that the new rubber is a lot deeper by a heavy 1/8". Where if I ever get them together the rubber will really be climbing up the glass and will be more than visible. Any suggestions would be greatly appreciated. Especially going around the corners of the glass.
Thanks Doug
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
#49277
Sat Feb 17 2007 07:16 PM
|
Joined: Jun 2002
Posts: 163
Petro Enthusiast
|
Petro Enthusiast
Joined: Jun 2002
Posts: 163 |
After you install the glass and bezzel in the door get a new razor blade and run around the inside edge of the bezzel...this will trim the 101 to the size of the bezzel..I have seen 2 different size 101 rubber ..1 is large like yours and 1 is just right..I have had to trim alot with this oversize 101 that is out now..
Hope this helps
Mark Sconyers Memories Restored
|
|
|
#49278
Sat Feb 17 2007 07:39 PM
|
Joined: Jan 2005
Posts: 2,702
Veteran Member
|
OP
Veteran Member
Joined: Jan 2005
Posts: 2,702 |
Mark
Can't even get the glass/rubber inside the bezel, I've tried stretching the rubber all the way around, it ain't going to happen ? I have all original ad glass and bezels... I'm trying to put 10 lbs of $h** in a 5 lb bag. Staring to see why reproduction glass is smaller ?
Thanks Doug
|
|
|
#49279
Sat Feb 17 2007 09:23 PM
|
Joined: Jan 2005
Posts: 356
Petro Enthusiast
|
Petro Enthusiast
Joined: Jan 2005
Posts: 356 |
Hey Doug, Try using some lubricant like maybe a drop or two of dish soap. Also I see that Gas Pump Heaven has 3 sizes of R101 listed in their book. Kent.
|
|
|
#49280
Sat Feb 17 2007 09:43 PM
|
Joined: Jan 2005
Posts: 356
Petro Enthusiast
|
Petro Enthusiast
Joined: Jan 2005
Posts: 356 |
Just noticed they have the U rubber listed as R100A R100B and R101. All U shaped. I did a 70 and she's a tight one. You may want to buy a couple feet of each to figure out which one works best and then go with that one. Kent.
|
|
|
#49281
Sun Feb 18 2007 06:04 AM
|
Joined: Dec 2006
Posts: 1,064 Likes: 2
Veteran Member
|
Veteran Member
Joined: Dec 2006
Posts: 1,064 Likes: 2 |
I just went through the same problem. So I carefully cut 4 separate pieces mitered at corners & it made a world of difference of fitting. When finished you couldn't tell that I cheated looking at it from the outside.
|
|
|
#49282
Mon Feb 19 2007 03:31 PM
|
Joined: Jan 2005
Posts: 2,702
Veteran Member
|
OP
Veteran Member
Joined: Jan 2005
Posts: 2,702 |
Thanks for the replies, going to buy new rubber and try it again.
|
|
|
|
|
|