Oldgas.com Home  
Home | Help | Events | Auctions | Parts | Pictures | Contact
Previous Thread
Next Thread
Print Thread
help needed with Coke cooler parts #588813
Sat Dec 27 2014 09:35 PM
Sat Dec 27 2014 09:35 PM
Joined: Nov 2014
Posts: 22
Adk Mtns, NY
KlockKing Offline OP
Member
KlockKing  Offline OP
Member
Joined: Nov 2014
Posts: 22
Adk Mtns, NY
I bought and then sold a coke machine last year, and these lids and panels were stacked inside. Iím tired of tripping over them, and would like to sell them. My problem is that I have zero idea what specific coolers/machines these parts belong to. Iíve numbered them in the photo, and below I will give rough measurements in inches for each piece. Any help from the folks that know a lot more about soda machines than I do would be much appreciated.
thanks
Paul
1-24 x 8ĺ
2-28 x 15ľ
3-30 x 11ĺ this lid has led a hard life. Looks to have been a favorite landing spot for a lot of rear ends.
4-28 x 12Ĺ
5-12ĺ x 10
6-29 7/8 x 12

coke  (1).JPGcoke  (2).JPG
Re: help needed with Coke cooler parts [Re: KlockKing] #588849
Sun Dec 28 2014 07:27 AM
Sun Dec 28 2014 07:27 AM
Joined: Jun 2009
Posts: 611
Georgia
coheley5 Offline
Petro Enthusiast
coheley5  Offline
Petro Enthusiast
Joined: Jun 2009
Posts: 611
Georgia
Looks like you have some good parts to a cavalier ice chest . You need a good frame to put back on.


Remember you are only as good as your help
If you don't make any noise no one will hear you!
Re: help needed with Coke cooler parts [Re: coheley5] #589399
Tue Dec 30 2014 07:31 PM
Tue Dec 30 2014 07:31 PM
Joined: Jul 2009
Posts: 68
Stuart, Fl
SodaJim Offline
Active Member
SodaJim  Offline
Active Member
Joined: Jul 2009
Posts: 68
Stuart, Fl
Appear to be from a large Westinghouse/Cavalier chest cooler, WD-20, WD-22, C-20, C22...
#1 is definitely the center panel between lids on a large cooler

Hopefully helpful,
Jim

Re: help needed with Coke cooler parts [Re: SodaJim] #589452
Wed Dec 31 2014 04:58 AM
Wed Dec 31 2014 04:58 AM
Joined: Nov 2014
Posts: 22
Adk Mtns, NY
KlockKing Offline OP
Member
KlockKing  Offline OP
Member
Joined: Nov 2014
Posts: 22
Adk Mtns, NY
That was exactly what I was hoping for, thank you. When I first posted this thread, JimT suggested I might get some help from the link in your sig block, soda-machines.com. I submitted my registration, but sadly I have yet to hear back from them and be approved. Thanks very much for the assist.
Paul

Re: help needed with Coke cooler parts [Re: KlockKing] #589632
Wed Dec 31 2014 08:43 PM
Wed Dec 31 2014 08:43 PM
Joined: Jul 2009
Posts: 68
Stuart, Fl
SodaJim Offline
Active Member
SodaJim  Offline
Active Member
Joined: Jul 2009
Posts: 68
Stuart, Fl
Paul,
Contact me off list so I can resolve your registration issue!
Jim

Re: help needed with Coke cooler parts [Re: SodaJim] #589859
Fri Jan 02 2015 06:15 AM
Fri Jan 02 2015 06:15 AM
Joined: May 2014
Posts: 681
New York
2 Gallon Luke Offline
Petro Enthusiast
2 Gallon Luke  Offline
Petro Enthusiast
Joined: May 2014
Posts: 681
New York
looks like parts off a large Westinghouse chest.I parted one out last year.


Good oil cans don't wait for people, people wait for them.

Moderated by  Oldgas, Ryan Underthun 

Click for an eBay Search Form and lots more live petro auction listings

Copyright © 2018 Primarily Petroliana Interactive, All Rights Reserved

Powered by UBB.threads™ PHP Forum Software 7.6.1.1