Oldgas.com Home

Home | Help | Events | Classifieds | Bookstore | Pictures | Auctions | Links | Collectors | Parts | Contact

Topic Options
#124325 - Tue Oct 23 2007 10:30 PM BENNETT 76/77 FRAME AND COMPUTER
WASHINGTONCHIEF Offline
Active Member

Registered: Thu Apr 13 2006
Loc: Vancouver WA
I need the frame work and computer assy for my 76 pump, I have the top, bottom, bezels, and good skins, somebody torched the rest and threw it away.

------------------
WANTED
Washington Chief, Oregon Chief, Idaho Chief, Montana Chief, Wasatch
_________________________
WANTED
Washington Chief, Oregon Chief, Idaho Chief, Montana Chief, Wasatch, Sunset, Veltex, Chevrolet

Top
#124326 - Wed Oct 24 2007 04:57 PM Re: BENNETT 76/77 FRAME AND COMPUTER
dodogas Offline
Veteran Member

Registered: Sat Jan 25 2003
Loc: Kelowna British Columbia Canad...
I have the Canadian Version the S.S.E.

Frame cosists of 4 pipes about 1 inch dia.. so that is 3/4 pipe I think.. by 5 1/2 ft long. One end has short pie thread and threads into the top, bottom has longer thread, straight I presume about 2 inches or so, fastens to base with jamb nuts top and bottom.
Computer sits on a shelf about 1/16 steel fits between the pipes with 2 edges bent down at 90. then U bolts fasten this to the frame pipes.
Another by the hose outlet, its about 3/4 angle iron again held by U bolts.

That is the whole frame..

Top
#124327 - Wed Oct 24 2007 05:43 PM Re: BENNETT 76/77 FRAME AND COMPUTER
dodogas Offline
Veteran Member

Registered: Sat Jan 25 2003
Loc: Kelowna British Columbia Canad...
I would trade drawings of trhese parts for tracings of your skins..use masking(bodyshop) or butcher paper, trace out, then fold to mail..

Top
#124328 - Wed Oct 24 2007 11:21 PM Re: BENNETT 76/77 FRAME AND COMPUTER
WASHINGTONCHIEF Offline
Active Member

Registered: Thu Apr 13 2006
Loc: Vancouver WA
Tracing my panels I can do for you, but I probably need some pictures to put this pump back together, there is enough of the old pipe, jamb nuts, and the mounting plate for the computer, to figure out the pipe. However an exact length, and knowing that it is straight pipe, would be a big help. What I do not know (and pictures may help)is what the panels rest against, and what the corner trim pieces screw to.
The pieces that I have are too nice to just use for parts, it needs to be put back together, looks like it had been stored inside for years, who knows why the frame work was cut up and thrown away.
_________________________
WANTED
Washington Chief, Oregon Chief, Idaho Chief, Montana Chief, Wasatch, Sunset, Veltex, Chevrolet

Top
#124329 - Thu Oct 25 2007 01:19 AM Re: BENNETT 76/77 FRAME AND COMPUTER
dodogas Offline
Veteran Member

Registered: Sat Jan 25 2003
Loc: Kelowna British Columbia Canad...
There is an inner rail that looks similar to the outer rail but it is thicker and tapped, my pump needs at least 1 made.

The skins rest against this, and the corner trims hold all in place.

I will go a bit custom on mine but the skin tracings will give me the general dimensions and starting point.

Top
#124330 - Sun Oct 28 2007 01:28 AM Re: BENNETT 76/77 FRAME AND COMPUTER
jrwienri Offline
Petro Enthusiast

Registered: Thu Jun 21 2001
Loc: Gilbert, AZ 85234
Here are a few pics of my 77 frame











The tall heavy metal corner rails (See photo above)screw on with 2 screws 1 at the top and 1 bottom to the top and bottom castings. The outer trim pieces that hold the skins on screw to this with 5 screws down the center. Ron Scobie has the outer trim pieces in polished stainless but not the heavy corner rails. There is also a flat center trim strip that fits down the center of the corner trim held on by the same 5 screws. Scobie has this too. There are an additional 2 small sheet metal pieces per side that screw on at the sides of the face bezels to complete the sheet metal on the front and back by the bezels.
Hope this helps, Jeff




[This message has been edited by jrwienri (edited 10-28-2007).]

Top
#124331 - Sun Oct 28 2007 10:57 AM Re: BENNETT 76/77 FRAME AND COMPUTER
dodogas Offline
Veteran Member

Registered: Sat Jan 25 2003
Loc: Kelowna British Columbia Canad...
Interesting. mine only has one angle iron bracket higher than the computer shelf.. I will double check.. and Yours seems to have an extra piece on the side holding that knob. I will have another look.


I will take another look at mine.

Wa Chief, sounds like needs corner rails and trim. I will make 1 corner rail for mine, I am missing one.. I think they would be a hassle to ship across the border anyway. (unless cut in 1/2 and rewelded)

[This message has been edited by dodogas (edited 10-28-2007).]

Top
#124332 - Sun Oct 28 2007 11:38 AM Re: BENNETT 76/77 FRAME AND COMPUTER
jrwienri Offline
Petro Enthusiast

Registered: Thu Jun 21 2001
Loc: Gilbert, AZ 85234
Dodo,
Since mine is a clockface it needs 2 angles to hold each side of the clock mech. I didn't install it but there is also another shelf that goes near the bottom that held the motor. 77 clocks have a unique reset crank system that is a ratcheting mechanism. It resets in one direction and slips in the other.
Jeff

Top
#124333 - Sun Oct 28 2007 09:47 PM Re: BENNETT 76/77 FRAME AND COMPUTER
WASHINGTONCHIEF Offline
Active Member

Registered: Thu Apr 13 2006
Loc: Vancouver WA
Jeff
Thanks for the great detail pics, I now know what I am missing (the inner corner braces) now all I have to do is find them, or fabricate.
Also a Thank You to all the others who have respnded to my posting.
Todd
_________________________
WANTED
Washington Chief, Oregon Chief, Idaho Chief, Montana Chief, Wasatch, Sunset, Veltex, Chevrolet

Top
#124334 - Mon Oct 29 2007 06:42 AM Re: BENNETT 76/77 FRAME AND COMPUTER
jkyocom Offline
Veteran Member

Registered: Fri Dec 15 2006
Loc: GA

I do make a 77 clock mech if you may be interested.Crank it one way , it will work, turn in reverse it will reset.
Thanks
Joe

[This message has been edited by jkyocom (edited 10-29-2007).]
_________________________
Veeder Root Rebuilds.....since 1987
Veeder Root Identification CD
Clock Repair
jkyocom@bellsouth.net

Top
#124335 - Tue Oct 30 2007 11:05 AM Re: BENNETT 76/77 FRAME AND COMPUTER
dodogas Offline
Veteran Member

Registered: Sat Jan 25 2003
Loc: Kelowna British Columbia Canad...
Wa Chief,
If your sight glass stuff looks different than shown I have info for mounting bracket, it is used if your inner top has tapped holes 8 in apart in the same plane as your faces.

From flat on your inner top to flat on your base.inner measurement is 61 1/2 on mine... adjustment for this is made with the Jam nuts above and below bottom casting.

Computer shelf is 40 inches up from the flat area on base where the pipes go thru.

I can draw it out and send but will wait to see what your manifold uses for hanging.

Top

Moderator:  Oldgas, Ryan Underthun, Watchdog2 

Click on magnifying glass icon on lower left to search eBay

Copyright © 2016 Primarily Petroliana Interactive, All Rights Reserved