#150878
Thu Sep 03 2009 02:18 PM
|
Joined: Aug 2003
Posts: 99
Active Member
|
OP
Active Member
Joined: Aug 2003
Posts: 99 |
This is a long shot, but does anybody have the supports that hold the cylinder assm to the tube assm? They also are the glides for the slider ring. They go behind the 3 Volute covers in the middle of the pump. Thanks, Joe
Joe Iaccino
|
|
|
|
Joined: Nov 2008
Posts: 1,627
Veteran Member
|
Veteran Member
Joined: Nov 2008
Posts: 1,627 |
Joe -- Hi ! I am in the middle of restoring a Wayne 492-- Would you be able to let me know what the Piping looks like in the middle of the glass cylinder -- picture would help-- Thanks Tom
|
|
|
|
Joined: Aug 2003
Posts: 99
Active Member
|
OP
Active Member
Joined: Aug 2003
Posts: 99 |
Are you referring to the elecrical conduit on the outside or the gas overfill tube on the inside? Joe
Joe Iaccino
|
|
|
|
Joined: Nov 2008
Posts: 1,627
Veteran Member
|
Veteran Member
Joined: Nov 2008
Posts: 1,627 |
Joe-- I am talking about the gas overfill tubes on the inside-- Tom
|
|
|
|
Joined: Aug 2003
Posts: 99
Active Member
|
OP
Active Member
Joined: Aug 2003
Posts: 99 |
Tom i'm trying to straighten out that mess in mine also. There is a short inverted piece for drain back & one that looks like a mushroom for gas coming in. The tall one that i've seen is machined down at the top & had a stainless cover over it. I don't know if that's correct. There's a guy who's handle is "Morgan" who has been helping me out on mine....Joe
Joe Iaccino
|
|
|
|
Joined: Aug 2003
Posts: 99
Active Member
|
OP
Active Member
Joined: Aug 2003
Posts: 99 |
Tom I now have a stock overfill pipe if you still need infomation Joe
Joe Iaccino
|
|
|
|
Joined: Nov 2008
Posts: 1,627
Veteran Member
|
Veteran Member
Joined: Nov 2008
Posts: 1,627 |
Joe-- that would help greatly-- Is there 1 or 2 pipes including the mushroom cap ? Also what have you done for the keyed lock ? Thanks Tom
|
|
|
|
Joined: Aug 2003
Posts: 99
Active Member
|
OP
Active Member
Joined: Aug 2003
Posts: 99 |
Tom There are 3 threaded hole in the base one for the "mushroom". One for the overfill pipe, & one for the "fuel in". It is a couple inches tall & flaired on the inside. The overfill pipe is regular pipe that hase been machined down at the top for a sleeve...possibly stainless
I don't know what I will do for a lock. The lock shops have something that is close but because I had to purchase a replacement handle, the actual I.D. is unknown. Joe
Joe Iaccino
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
I also found something @ a lock shop that is close. I tried to turn housing down, but found it didn't like machining. Another thought was to bore out the handle to fit cylinder housing or make a sleave for lock mech. Then I got side tracked AGAIN.
|
|
|
|
Joined: Nov 2008
Posts: 1,627
Veteran Member
|
Veteran Member
Joined: Nov 2008
Posts: 1,627 |
Dick --If you get it to work there is probably a lot guys that could use the lock solution -- TS
|
|
|
|
|