|
#251185
Thu Apr 28 2011 09:25 AM
|
Joined: Sep 2009
Posts: 1,452
Veteran Member
|
OP
Veteran Member
Joined: Sep 2009
Posts: 1,452 |
Looking for the round metal plate that goes behind the spinner on a Tokheim 36B. Please PM if you have one. Thanks Lee
Looking for anything JENNEY OIL OR GAS
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
Lee--What does it measure? I have a couple but don't remember if they're from a 36B or from a Wayne 60??
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Sep 2009
Posts: 1,452
Veteran Member
|
OP
Veteran Member
Joined: Sep 2009
Posts: 1,452 |
It's 2 3/4" across
Center hole is 5/8"
The two screw holes are 1&1/16" on center.
Thanks,
Looking for anything JENNEY OIL OR GAS
|
|
|
|
Joined: Nov 2002
Posts: 4,962 Likes: 17
Moderator
|
Moderator
Joined: Nov 2002
Posts: 4,962 Likes: 17 |
I dont have any at this time, but here is a picture for reference in case somebody does not know what they look like. http://www.thepumpdump.com/parts/main.php?g2_itemId=443
FREEDOM oil items wanted.
|
|
|
|
Joined: Sep 2009
Posts: 1,452
Veteran Member
|
OP
Veteran Member
Joined: Sep 2009
Posts: 1,452 |
Thanks Ryan,
I saw you were out of them, when I posted this but I didnt think of posting a picture with it.
Looking for anything JENNEY OIL OR GAS
|
|
|
|
Joined: May 2004
Posts: 517
Petro Enthusiast
|
Petro Enthusiast
Joined: May 2004
Posts: 517 |
You could make them out of some sheet metal. It would not be that hard.
Randy
Always looking for Hy-Flash Gas/Miller Oil, Hi-Speed Gas/ Hickok Oil and Paragon Refining items from Toledo,Ohio.
|
|
|
|
Joined: Sep 2009
Posts: 1,452
Veteran Member
|
OP
Veteran Member
Joined: Sep 2009
Posts: 1,452 |
I thought of that but the only way I could is with a hole saw.
Unless you have any other ideas of how to make one?
I'm going to chrome it so it needs to be prety clean cut.
Thanks,
Looking for anything JENNEY OIL OR GAS
|
|
|
|
Joined: May 2004
Posts: 517
Petro Enthusiast
|
Petro Enthusiast
Joined: May 2004
Posts: 517 |
If you go to metal fabrication shop / sheetmetal shop which have the tools. That would be the easy way. But you will need the thickness of the metal,size and hole sizes and locations.
Randy
Always looking for Hy-Flash Gas/Miller Oil, Hi-Speed Gas/ Hickok Oil and Paragon Refining items from Toledo,Ohio.
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
& have them make w/ Mirror Stainless
|
|
|
|
|
|