|
#304066
Sat Feb 11 2012 01:34 PM
|
Joined: Dec 2011
Posts: 209 Likes: 4
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2011
Posts: 209 Likes: 4 |
If anyone ever runs across a question mark/shepherds staff pole similar to the one in the photo below, please contact me. Thanks.
|
|
|
|
Joined: Sep 2004
Posts: 853
Petro Enthusiast
|
Petro Enthusiast
Joined: Sep 2004
Posts: 853 |
That one pictured is about an hour from here. Neat poles good luck!
Joey
|
|
|
|
Joined: Aug 2011
Posts: 472
Petro Enthusiast
|
Petro Enthusiast
Joined: Aug 2011
Posts: 472 |
I know where one is with a texaco in it . And a buddy of mine has a couple of just the poles i might be getting them shortly and might sell one .
|
|
|
|
Joined: Feb 2007
Posts: 472
Petro Enthusiast
|
Petro Enthusiast
Joined: Feb 2007
Posts: 472 |
Shouldn't be too hard to make those.
Still looking for that Union 76 ball And I collect big old porcelain neon signs
|
|
|
|
Joined: Oct 2008
Posts: 2,786 Likes: 165
Veteran Member
|
Veteran Member
Joined: Oct 2008
Posts: 2,786 Likes: 165 |
I made one recently for my 42" lighted pure sign It turned out great. Ran the wire inside to hide it.
|
|
|
|
Joined: Sep 2007
Posts: 19,470 Likes: 1022
Veteran Member
|
Veteran Member
Joined: Sep 2007
Posts: 19,470 Likes: 1022 |
what size pipe did you use to assemble pole? what diameter is at the question mark? how tall is pole from ground up?
RANDY
|
|
|
|
Joined: Oct 2008
Posts: 2,786 Likes: 165
Veteran Member
|
Veteran Member
Joined: Oct 2008
Posts: 2,786 Likes: 165 |
1" black pipe easier to bend, It is 13' tall because it is inside. I have a wall that comes out at a right angle to the long wall and I made special brackets to hold the pole up.
|
|
|
|
Joined: Dec 2011
Posts: 209 Likes: 4
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2011
Posts: 209 Likes: 4 |
How did you make the bend in the pipe?
|
|
|
|
Joined: Sep 2007
Posts: 19,470 Likes: 1022
Veteran Member
|
Veteran Member
Joined: Sep 2007
Posts: 19,470 Likes: 1022 |
I made one recently for my 42" lighted pure sign It turned out great. Ran the wire inside to hide it. would you post picture of your sign within question mark of pole?
RANDY
|
|
|
|
Joined: Oct 2008
Posts: 2,786 Likes: 165
Veteran Member
|
Veteran Member
Joined: Oct 2008
Posts: 2,786 Likes: 165 |
I will when I can lower my resolution on my camera, it wont let me resize.
|
|
|
|
Joined: Dec 2011
Posts: 8,818 Likes: 2
Veteran Member
|
Veteran Member
Joined: Dec 2011
Posts: 8,818 Likes: 2 |
I wouldn't use 1" pipe. A 42" sign would trap to much wind. 1" pipe cannot support that kind of wind load. Structurally that pipe will fatigue and fail. Wouldn't want to be near that 42" sign when a gust of wind launches it, and chunks/pieces of 1" pipe.
Dave GILL, Dave's Garage & Memorabilia, Inc.
|
|
|
|
|
|