|
#458552
Tue Aug 27 2013 05:18 PM
|
Joined: Sep 2009
Posts: 1,452
Veteran Member
|
OP
Veteran Member
Joined: Sep 2009
Posts: 1,452 |
Does any one have a pic of the inside of a Wayne 40 visi? I need to see the inside componets. Thanks Lee
Looking for anything JENNEY OIL OR GAS
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Spinner looks like an UN-cook Ravioli Noodle.
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
Lee--Hope this does it for you! By the way--does the spring on a tok 34 visi go on the top or the bottom of the little center spinner??
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Oct 2003
Posts: 1,663 Likes: 25
Veteran Member
|
Veteran Member
Joined: Oct 2003
Posts: 1,663 Likes: 25 |
kevin mine is on top, same as a tok 850. chris
|
|
|
|
Joined: Feb 2002
Posts: 2,772 Likes: 3
Veteran Member
|
Veteran Member
Joined: Feb 2002
Posts: 2,772 Likes: 3 |
Goes on the top of the spinner same as an 850 Visi.
Larry
In memory of DB 9/12/49 - 8/28/14
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
HHhhmmm? Doesn't look quite right? Sits on the spinner in the glass tube ok, but the hump in the cover is bigger around than the spring and it sits a little cockeyed?? I know, I know--I shoulda taken a picture when I took it apart!
Last edited by K W FRITH; Tue Aug 27 2013 06:50 PM.
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Feb 2002
Posts: 2,772 Likes: 3
Veteran Member
|
Veteran Member
Joined: Feb 2002
Posts: 2,772 Likes: 3 |
The "hump" should only be about 3/8 inch the spring is 1 inch o.d. 1 3/4 inch long
This pic is not original spring. The one in pic is tapered,,just something I had originals are as I said 1 " o.d. x 1 3/4" long
Larry
Last edited by st.rod; Tue Aug 27 2013 07:01 PM.
In memory of DB 9/12/49 - 8/28/14
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
Comes apart easy, so maybe I'll just take it back apart and photo it. Any of you guys have a close up pic of one together??
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Sep 2009
Posts: 1,452
Veteran Member
|
OP
Veteran Member
Joined: Sep 2009
Posts: 1,452 |
Thanks for the posts and pix. Here is my problem, in the pix below you can see where the spinner end goes into the set hole on the bottom. But the spinner is not tall enough to reach the top, and if it was, there is no set hole like in Kevin's pic. I wonder if I am missing a part for the inside.
Looking for anything JENNEY OIL OR GAS
|
|
|
|
|
|