|
#523736
Thu Mar 27 2014 06:26 AM
|
Joined: Jul 2010
Posts: 850
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Jul 2010
Posts: 850 |
Wondering what anyone might know about a base for a twin Wayne 60 / model 65? I see it in Jacks book and there is one on eBay now (item 331162173417). What are the odds of turning another one up, or I guess if you had one you could easily make another. Anyone have one/build one? Thanks
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Dec 2011
Posts: 8,818 Likes: 2
Veteran Member
|
Veteran Member
Joined: Dec 2011
Posts: 8,818 Likes: 2 |
I.M.O. cast iron bases are usually the easiest part to find. Even on a pump left outside in the elements and allowed to rot away the base would survive in pretty good condition.
Having said that, I think it'll take a bit of effort to find the other half of this base. Pretty rare piece.
Dave GILL, Dave's Garage & Memorabilia, Inc.
|
|
|
|
Joined: Apr 2003
Posts: 2,195 Likes: 74
Veteran Member
|
Veteran Member
Joined: Apr 2003
Posts: 2,195 Likes: 74 |
your right dave, i have half of a wayne 70 base like this and still trying to find the other half, missed one about 10 years ago at Red Deer swap and still looking..
Wanted early tin litho signage. petro, farm, auto, etc.
|
|
|
|
Joined: Jul 2010
Posts: 850
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Jul 2010
Posts: 850 |
Thanks for input, if you have the bases and a couple 60s - I would think the center cabinet is something that could be built and made to look close to an original? Doesn't look too complicated? Hard to judge from the photo?
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Took me almost 15yrs to buy 1/2 of another 36B Twin. A few were offered, but at Inflated Prices.
|
|
|
|
Joined: Jan 2009
Posts: 5,980 Likes: 24
Veteran Member
|
Veteran Member
Joined: Jan 2009
Posts: 5,980 Likes: 24 |
If at last resort, you could recast for they look pretty much identical. Leaving room or adding on for the shrinkage.
Craig
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Typical Shrinkage for Cast Iron is 1/8" per ft, Alum is 3/16" per ft. Build you original part up outside w/ Bondo before casting.
|
|
|
|
Joined: Jan 2009
Posts: 5,980 Likes: 24
Veteran Member
|
Veteran Member
Joined: Jan 2009
Posts: 5,980 Likes: 24 |
Great thought, I was using aluminum and JB weld.
Craig
|
|
|
|
Joined: May 2011
Posts: 184
Petro Enthusiast
|
Petro Enthusiast
Joined: May 2011
Posts: 184 |
As I recall, Miles Little in North Carolina is (was) the expert in converting 60s into 65s. I believe he produced the bases also. He is not a member here but I may have his number if it helps.
SW
Always looking for more pumps, meters and signs. Some say it is a problem, I say it is a solution
|
|
|
|
|
|