|
Joined: Sep 2008
Posts: 1,749
Veteran Member
|
Veteran Member
Joined: Sep 2008
Posts: 1,749 |
Considering how little is out there on Grotken, I would say anything possibly could be considered correct . Ed Shaver
see ya on the road folks !
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
I've seen a few of these pumps in different collections & None of them had the light on top. All looked just like the one above w/ the ball knob. Believe what ya want as there are only 2 views of this in the book for the Pump Experts!
|
|
|
|
Joined: Nov 2000
Posts: 7,791 Likes: 9
Veteran Member
|
Veteran Member
Joined: Nov 2000
Posts: 7,791 Likes: 9 |
Possibly the top that you have is worth the same as the bottom you don't have.
Jack Sim
Author, 1st & 2nd editions of Gas Pump ID book, 3rd edition is now available at www.gaspumpbible.comAir Meter ID book also available
|
|
|
|
Joined: Jul 2002
Posts: 1,951 Likes: 1
Veteran Member
|
Veteran Member
Joined: Jul 2002
Posts: 1,951 Likes: 1 |
Jim, if you are asking for a photo of the top of the "center piece", I don't have that. But, I don't believe the "center piece" is needed as an attachment to a curb pump. My understanding is that what Mario has, is the cylinder with top and bottom castings, plus the center section, which would have bolted to the top of a Groetken pump. If you remove that center section, you'd have exactly what my photos show ie: a Groetken visible attachment. I believe the center section is only needed as part of the original pump.
Mr. Wadhams, yes, there are four bolt holes on the perimiter of where the pipe would screw into the bottom casting.
I also believe that the little ball on the top of the cylinder is not related to any light that might have been on top of the pump.
Hope this helps. Don
Don "oltoydoc" Sherwood oltoydoc@vintagegas.com (310)415-9562 Cel. Vintage Gas
|
|
|
|
Joined: Mar 2012
Posts: 10
Member
|
OP
Member
Joined: Mar 2012
Posts: 10 |
Thanks to all that have replied to this post. To add to the lil ball on top confusion, I believe this was some kind of vent for easy flowing of the fuel because I have found three 1/8"+/- dia vent holes equally spaced on it?
|
|
|
|
Joined: Nov 2006
Posts: 27
Active Member
|
Active Member
Joined: Nov 2006
Posts: 27 |
I have a restored pump. It is as yours. Your top fits on a round steel cylinder that is bent to a cylinder shape and is rivited in a straight line from top to bottom. Looks like the photo in the ad. It has the knob on top and no light. Mine has a globe covering the knob. I suspect the body is designed to enclose a curb pump that was already in the buyers possession. I still have the actual pump inside it. I'll look and see if the manufacturer of it is visable. I'll post some photos, too.
Thanks...Poppy
|
|
|
|
Joined: Dec 2006
Posts: 3,369 Likes: 7
Veteran Member
|
Veteran Member
Joined: Dec 2006
Posts: 3,369 Likes: 7 |
My buddy has a 5 gal Groetken and it don't look nuttin like dat
Veeder Root Rebuilds.....since 1987 Veeder Root Identification CD Gas Pump Clock Repair jkyocom@bellsouth.net
|
|
|
|
Joined: Nov 2006
Posts: 27
Active Member
|
Active Member
Joined: Nov 2006
Posts: 27 |
I would post photo's of my restored pump if I could upload them Jack!!! or a remedy to do it without giving up my email address
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Down load to Image Shack or Photo Bucket [BOTH are FREE IMAGE HOSTING SITES] & select the link for FORUMS to Copy & Paste.
[so easy even a girl scout could figure it out]
Last edited by Dick Bennett; Tue Jul 09 2013 07:58 PM.
|
|
|
|
Joined: Jul 2010
Posts: 70
Active Member
|
Active Member
Joined: Jul 2010
Posts: 70 |
Page 30 of the "Value Guide to Gas Station Memorabilia" has a pic of what looks like this pump.
|
|
|
|
Joined: Dec 2007
Posts: 343
Petro Enthusiast
|
Petro Enthusiast
Joined: Dec 2007
Posts: 343 |
Not sure that I can add anything to this except a couple pics of my Groetken 5 gallon, obviously a different model....
|
|
|
|
Joined: Dec 2006
Posts: 3,369 Likes: 7
Veteran Member
|
Veteran Member
Joined: Dec 2006
Posts: 3,369 Likes: 7 |
That is what my buddy's Groetken looks like His has original hail screen & numbers people say are the wrong ones but I know they are factory...you don't know everything guys
Veeder Root Rebuilds.....since 1987 Veeder Root Identification CD Gas Pump Clock Repair jkyocom@bellsouth.net
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
That is what my buddy's Groetken looks like His has original hail screen & numbers people say are the wrong ones but I know they are factory...you don't know everything guys I'll ADMIT to that, NO ONE EVER WILL. Pump companies did make 1 of a kind/special pumps for customers. Some pumps were modified by secondary companies to fit their customers needs. The 5gal Broken Groetken I had looked like H1's, which is Nothing like the head unit [as said above] at beginning of this thread.
|
|
|
|
Joined: Nov 2006
Posts: 27
Active Member
|
Active Member
Joined: Nov 2006
Posts: 27 |
Thanks...Poppy
|
|
|
|
Joined: Aug 2014
Posts: 139
Petro Enthusiast
|
Petro Enthusiast
Joined: Aug 2014
Posts: 139 |
|
|
|
|
|