#681179
Sun Mar 05 2017 12:42 PM
|
Joined: Dec 2001
Posts: 3,004 Likes: 27
Veteran Member
|
OP
Veteran Member
Joined: Dec 2001
Posts: 3,004 Likes: 27 |
OK I know this has been discussed on here before but having an issue getting one off my 60. I have been on it with a pipe wrench and a three foot long cheater pipe and I can't budge it. Threads off counter clock wise right? Not sure what else to do.
Drive with Care and Buy Sinclair!! I buy Sinclair globes, signs, cans, ect.
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Aug 2004
Posts: 1,689 Likes: 17
Veteran Member
|
Veteran Member
Joined: Aug 2004
Posts: 1,689 Likes: 17 |
Yes, counter clockwise. Sometimes heat and leverage is the only way. The nut removal tool is helpful as well.
|
|
|
|
Joined: Apr 2003
Posts: 2,195 Likes: 74
Veteran Member
|
Veteran Member
Joined: Apr 2003
Posts: 2,195 Likes: 74 |
Wanted early tin litho signage. petro, farm, auto, etc.
|
|
|
|
Joined: Dec 2001
Posts: 3,004 Likes: 27
Veteran Member
|
OP
Veteran Member
Joined: Dec 2001
Posts: 3,004 Likes: 27 |
Ok thanks. Never have seen how the nut removal tool would help other than getting a grip on it. How do you get any pressure on it with that?
Drive with Care and Buy Sinclair!! I buy Sinclair globes, signs, cans, ect.
|
|
|
|
Joined: Aug 2004
Posts: 1,689 Likes: 17
Veteran Member
|
Veteran Member
Joined: Aug 2004
Posts: 1,689 Likes: 17 |
More for if you're trying to save the nut without breaking off the tabs. If you don't care about that, pipe wrench is the way to go. Heat it up a little and put a 3' pipe on for leverage...it'll come off.
|
|
|
|
Joined: Oct 2000
Posts: 1,306 Likes: 32
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 1,306 Likes: 32 |
Ok thanks. Never have seen how the nut removal tool would help other than getting a grip on it. How do you get any pressure on it with that? Grip and torque are the two key elements in removing anything threaded.
|
|
|
|
Joined: Jan 2007
Posts: 640
Petro Enthusiast
|
Petro Enthusiast
Joined: Jan 2007
Posts: 640 |
Kieth: Most makers of the Wayne Nut Wrench put a square 1/2 hole in the handle. This is for you to put a 1/2 Breaker Bar or ratchet for leverage. If there is white putty-looking material visible around the nut base, carve that out with a razor knife. Pre-soak for a few days with Liquid wrench all around glass and nut, and finally a LITTLE heat around perimeter of the nut only. You are trying to by heat, expand the nut and break the seal. Quickly apply increasing pressure on the nut with the wrench before it cools. Once the nut moves, don't stop before all the way off. You may squirt a little oil on threads as nut comes off. You may have to reverse direction a little sometimes. Remember: "Lefty-Loosey, Righty-Tighty" or clockwise=tighten, counterclockwise=loosen. Go slow to avoid damage or injury. Ed.
|
|
|
|
Joined: Jun 2004
Posts: 2,131 Likes: 76
Veteran Member
|
Veteran Member
Joined: Jun 2004
Posts: 2,131 Likes: 76 |
If Dick Bennett was still around he would remind you not to forget the beer. Richard
|
|
|
|
Joined: May 2016
Posts: 584 Likes: 35
Petro Enthusiast
|
Petro Enthusiast
Joined: May 2016
Posts: 584 Likes: 35 |
These were really tight on my Wayne 60. I used the sight glass removal nut from gas pump heaven, but when I put a cheater pipe on that square socket fitting it actually began to round out on the inside. So, I took a 3 lb sledgehammer to it. I hit the removal tool on the side of the tool where it flares out. I was able to get the nut to loosen by doing it that way. I didn't use any heat due to concern with breaking the sight glass. I did soak the threads with kroil beforehand.
BrianH
Brian H
|
|
|
|
Joined: May 2012
Posts: 1,871 Likes: 48
Veteran Member
|
Veteran Member
Joined: May 2012
Posts: 1,871 Likes: 48 |
Had the same problem with my ring wrench rounding out the corners so I welded on an old socket and have no problems since I did this.
Have gas all the time
|
|
|
|
Joined: May 2016
Posts: 584 Likes: 35
Petro Enthusiast
|
Petro Enthusiast
Joined: May 2016
Posts: 584 Likes: 35 |
Brian H
|
|
|
|
Joined: Dec 2001
Posts: 3,004 Likes: 27
Veteran Member
|
OP
Veteran Member
Joined: Dec 2001
Posts: 3,004 Likes: 27 |
Thanks guys. I am going to take all these tips and go at it again. Those darn things are tight though!
Drive with Care and Buy Sinclair!! I buy Sinclair globes, signs, cans, ect.
|
|
|
|
Joined: Dec 2002
Posts: 3,188 Likes: 1
Veteran Member
|
Veteran Member
Joined: Dec 2002
Posts: 3,188 Likes: 1 |
I made this tool a while back it works good. Probably took a half hour once I found the right sized pipe. Since I made this, I think I found out that you can make one out of an oxygen tank safety cap-the screw on guard. Use a long-three foot concrete pin or solid pipe for leverage and a little heat You will be surprised when you see how much torque you can put on there when you are pushing and pulling with two hands. They came out with that cheesy tool after my original dilemma. I like mine better. Heres a link http://www.oldgas.com/forum/ubbthreads.php?ubb=showflat&Number=208208#Post208208
Last edited by JimT; Mon Mar 06 2017 07:37 PM.
|
|
|
|
Joined: May 2016
Posts: 584 Likes: 35
Petro Enthusiast
|
Petro Enthusiast
Joined: May 2016
Posts: 584 Likes: 35 |
Jim, that is a great idea. You'll never break that thing!
BrianH
Brian H
|
|
|
|
Joined: Dec 2001
Posts: 3,004 Likes: 27
Veteran Member
|
OP
Veteran Member
Joined: Dec 2001
Posts: 3,004 Likes: 27 |
Still can't get this thing off. I have sprayed it, tried chipping out the putty but it is really hard and I have had a pipe wrench with a 3 foot long pipe on it and hit it with a sledge hammer and it still won't budge. Not sure what to do. I don't have anything to heat it with so I have not tried that.
Drive with Care and Buy Sinclair!! I buy Sinclair globes, signs, cans, ect.
|
|
|
|
|