#127321
Thu Jan 25 2007 02:25 AM
|
Joined: Apr 2006
Posts: 47 Likes: 2
Active Member
|
OP
Active Member
Joined: Apr 2006
Posts: 47 Likes: 2 |
When using this method to strip metal parts, does it compromise the part being cleaned in any way?
phmlpn
|
|
|
These topics are archived because they are older. You may not post new replies. Contact member through their email in their Profile or by PM message. Help with contacting members
|
|
#127322
Thu Jan 25 2007 02:36 AM
|
Joined: May 2004
Posts: 2,094 Likes: 4
Veteran Member
|
Veteran Member
Joined: May 2004
Posts: 2,094 Likes: 4 |
No,It's just soap and water!
Got Socony???
Tom
|
|
|
#127323
Thu Jan 25 2007 10:03 AM
|
Joined: Dec 2006
Posts: 3,369 Likes: 7
Veteran Member
|
Veteran Member
Joined: Dec 2006
Posts: 3,369 Likes: 7 |
Does this work for non-ferrous metals also???
Veeder Root Rebuilds.....since 1987 Veeder Root Identification CD Gas Pump Clock Repair jkyocom@bellsouth.net
|
|
|
#127324
Thu Jan 25 2007 10:31 AM
|
Joined: Jan 2003
Posts: 1,479
Veteran Member
|
Veteran Member
Joined: Jan 2003
Posts: 1,479 |
I use this to clean Model T Gas Tanks, Model T Transmission's and other parts - even the engine blocks can be done. The only thing I have found that is "eats" is babbit & aluminum. These parts will damage REAL QUICK and it tends to destroy the water/batch after you are done. That is ok - just drain and re-fill then re-treat and go again.
Now for SOAP - no - use arm & hammer washing SODA. It works BEST - but you should wash the parts REAL GOOD after soaking to get all the washing soda off - it is a corrosive. I then bead blast my parts in the blasting cab..
Travis E. Towle Topeka, Kansas
|
|
|
#127325
Thu Jan 25 2007 11:00 AM
|
Joined: May 2004
Posts: 2,094 Likes: 4
Veteran Member
|
Veteran Member
Joined: May 2004
Posts: 2,094 Likes: 4 |
Travis is correct about the washing soda I was using soap as a generic term! Tom
Got Socony???
Tom
|
|
|
#127326
Thu Jan 25 2007 12:46 PM
|
Joined: Dec 2006
Posts: 3,369 Likes: 7
Veteran Member
|
Veteran Member
Joined: Dec 2006
Posts: 3,369 Likes: 7 |
I was wondering if salt would work better than soap since it is a conductor in water but Travis answered that one.The washing soda is caustic, baking soda is a base, have you ever tried baking soda? It should have the same conductive properties and may not be as corrosive. Is it the electricity or the alkaline that lifts the paint or is it both? How is it you set up the electricity and what material does the tub need to be ,I had never heard of this untill a few months ago.Does it set up like electroplate??
[This message has been edited by jkyocom (edited 01-25-2007).]
[This message has been edited by jkyocom (edited 01-25-2007).]
[This message has been edited by jkyocom (edited 01-25-2007).]
[This message has been edited by jkyocom (edited 01-25-2007).]
Veeder Root Rebuilds.....since 1987 Veeder Root Identification CD Gas Pump Clock Repair jkyocom@bellsouth.net
|
|
|
#127327
Thu Jan 25 2007 05:01 PM
|
Joined: Jan 2006
Posts: 3,050
Veteran Member
|
Veteran Member
Joined: Jan 2006
Posts: 3,050 |
Anything Chevron I'd rather be flying.....
|
|
|
#127328
Thu Jan 25 2007 06:05 PM
|
Joined: Feb 2002
Posts: 2,772 Likes: 3
Veteran Member
|
Veteran Member
Joined: Feb 2002
Posts: 2,772 Likes: 3 |
Yes, Baking Soda and Laundry Soap is great. The Arm & Hammer is just boxed and ready to use. For me, I do not always have the Arm & Hammer product. But I always have baking soda and laundry soap! LARRY [This message has been edited by st.rod (edited 01-25-2007).]
In memory of DB 9/12/49 - 8/28/14
|
|
|
#127329
Fri Jan 26 2007 11:56 AM
|
Joined: Dec 2006
Posts: 3,369 Likes: 7
Veteran Member
|
Veteran Member
Joined: Dec 2006
Posts: 3,369 Likes: 7 |
so if it eats aluminun....does it hurt brass , copper??? Or is it basically for ferrous metals , iron, steel ??
Veeder Root Rebuilds.....since 1987 Veeder Root Identification CD Gas Pump Clock Repair jkyocom@bellsouth.net
|
|
|
#127330
Fri Jan 26 2007 12:41 PM
|
Joined: Jul 2005
Posts: 5,348 Likes: 1
Veteran Member
|
Veteran Member
Joined: Jul 2005
Posts: 5,348 Likes: 1 |
...try this, gotta have that 'www' in there, or it won't load: http://www.antique-engines.com/electrol.asp
Looking for better Gulf items: signs, globes, cans and paper - especially porcelain Gulf flanges, and Gulf A-38 & A-62 ad glass...
|
|
|
#127331
Fri Jan 26 2007 05:44 PM
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
jkyocom, It will eat up Babbit, Potmetal/Whitemetal,Magnesium & Alum.
[This message has been edited by Dick Bennett (edited 01-26-2007).]
|
|
|
#127332
Sun Feb 04 2007 01:20 PM
|
Joined: Jul 2000
Posts: 8,513 Likes: 293
Moderator
|
Moderator
Joined: Jul 2000
Posts: 8,513 Likes: 293 |
The original "How To" feature about electrolysis can now be found in the How To Archive. Paint Removal By Electrolysis ------------------ Jim "Oldgas" PottsYour host and moderator
Last edited by Oldgas; Thu Jul 30 2009 06:01 PM. Reason: Edit to correct non-working link
|
|
|
|
|