#261039
Thu Jun 30 2011 07:32 PM
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
Looking for frame rails (non-hinged style) for a Wayne 866 gas pump. Thanks.
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
They will need to know WIDE or NARROW frame.
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
I think all Wayne 60's are the same with the exception of wide or narrow as Dick mentioned. In my experience, they are all drilled and tapped the same but some have hinges installed & some don't. Am I right??
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Correct Kevin. The mounting brackets are different for a VR vs Clock mech., bonnet, site glass manifold, inner bezel reflectors & base.
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
Wide-body, clockface, non-hinged for a farm fresh Wayne 866.
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
|
|
|
|
Joined: Oct 2003
Posts: 1,663 Likes: 25
Veteran Member
|
Veteran Member
Joined: Oct 2003
Posts: 1,663 Likes: 25 |
good luck you will probably have to buy them 1 at a time as you can find them?? chris
|
|
|
|
Joined: Nov 2002
Posts: 4,962 Likes: 17
Moderator
|
Moderator
Joined: Nov 2002
Posts: 4,962 Likes: 17 |
I have a couple of right ones.
FREEDOM oil items wanted.
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
how do I reference right from left?
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Looking at the face, do you need the left or Right rails for that side [2 of ea = all 4]
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
One interesting thing is the porcelain doors on this pump were neither hinged nor church key style. They were held on by the same bolts as used on the bezels. The rails are tapped for the same thread size. Anyone seen this before? And it's factory original.
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
Thats different? Never seen before. Almost sounds like the rails would be on a 60S.
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
How could I confirm this?
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
There are a lot of unexplainable things that happened with pumps over the years as many parts were replaced with whatever was available and sometimes on assembly lines, things came out different than they were supposed to. Your 866 clockface should not have rails that are drilled and tapped. The frame rails on a 60S, had the lower section drilled and tapped to accept the lower cover below the display door. There are several ways to tell a display model from a reproduced one.
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Dec 2010
Posts: 635
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Dec 2010
Posts: 635 |
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Pump was ordered by ATLANTIC to their specs.
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Here is a panel for a WAYNE 60 for ATLANTIC; 160627218349 Holes on Right side look like it was made for hinges
|
|
|
|
|