Oldgas.com Home  
Home | Help | Events | Auctions | Parts | Pictures | Contact
Previous Thread
Next Thread
Print Thread
Page 1 of 2 1 2
Trim Plates For A Wayne 70 #61279
Sun Jun 25 2006 05:02 PM
Sun Jun 25 2006 05:02 PM
Joined: Jan 2005
Posts: 2,702
Saline, Mi USA
B
blacktee Offline OP
Veteran Member
blacktee  Offline OP
Veteran Member
B
Joined: Jan 2005
Posts: 2,702
Saline, Mi USA
Hey Guys:

I need some help here !!! I'm doing a Wayne 70. Working on the add glasses and face glasses. My parts list doesn't show the correct wording for these holders. Below are some pictures of the fastners. My question is ? Is there anyway to put them back in ? These go behind the stainless steel trim pieces. I have a bag full and want to keep this pump as original as possible. The guy that saves my *** here, will help me donate $100.00 to oldgas.com. I'm told they are made out of zinc ??

Give me some ideas guys !!!

Thanks, Doug






Please use For Sale forums to sell

Please - NO offers to Buy or Sell in this forum category

Statements such as, "I'm thinking about selling this." are considered an offer to sell.
Re: Trim Plates For A Wayne 70 #61280
Sun Jun 25 2006 05:08 PM
Sun Jun 25 2006 05:08 PM
Joined: Oct 2000
Posts: 22,780
Santa Paula, Calif
Dick Bennett Offline
Veteran Member
Dick Bennett  Offline
Veteran Member
Joined: Oct 2000
Posts: 22,780
Santa Paula, Calif
Sand lightly & JB WELD
db

------------------
**PUT A LID ON IT**
1qt RE-LIDDING

Re: Trim Plates For A Wayne 70 #61281
Sun Jun 25 2006 05:45 PM
Sun Jun 25 2006 05:45 PM
Joined: Nov 2005
Posts: 8,993
Antioch,IL
oldnfuelish Offline
Veteran Member
oldnfuelish  Offline
Veteran Member
Joined: Nov 2005
Posts: 8,993
Antioch,IL
works great!did it to mine!


Looking for gas,oil related clocks,especially neon and spinners .clock repair available. Mick
Re: Trim Plates For A Wayne 70 #61282
Sun Jun 25 2006 06:26 PM
Sun Jun 25 2006 06:26 PM
Joined: Dec 2001
Posts: 2,676
USA
keithia Offline
Veteran Member
keithia  Offline
Veteran Member
Joined: Dec 2001
Posts: 2,676
USA
They are supposed to clip in but the clip part is normally broken or they fit so loose they fall back out and don't hold. Poor design in my book. JB Weld sounds good.

Keith


Drive with Care and Buy Sinclair!! I buy Sinclair globes, signs, cans, ect.
Re: Trim Plates For A Wayne 70 #61283
Sun Jun 25 2006 06:55 PM
Sun Jun 25 2006 06:55 PM
Joined: Jan 2006
Posts: 3,041
On the plains of Colorado
Thunder II Offline
Veteran Member
Thunder II  Offline
Veteran Member
Joined: Jan 2006
Posts: 3,041
On the plains of Colorado
JB Weld....


Anything Chevron
[Linked Image]
I'd rather be flying.....
Re: Trim Plates For A Wayne 70 #61284
Sun Jun 25 2006 06:55 PM
Sun Jun 25 2006 06:55 PM
Joined: Feb 2006
Posts: 284
Carstairs, Alberta,formerly Sa...
K
Ken Bird Offline
Petro Enthusiast
Ken Bird  Offline
Petro Enthusiast
K
Joined: Feb 2006
Posts: 284
Carstairs, Alberta,formerly Sa...
Hi Fellas. When I did my 70, I didn't have any JB Weld handy, so I used some metal panel adhesive that we use in the autobody industry to "glue" on roof panels, door skins, etc. I know it's not that readily available to the general public, but it did work good. Just a little tid-bit that worked for me.
Ken.

Re: Trim Plates For A Wayne 70 #61285
Sun Jun 25 2006 09:24 PM
Sun Jun 25 2006 09:24 PM
Joined: Mar 2001
Posts: 577
Island County, Washington
G
gaspower Offline
Petro Enthusiast
gaspower  Offline
Petro Enthusiast
G
Joined: Mar 2001
Posts: 577
Island County, Washington
JB Weld and don't forget to run a tap down and clean the threads.

Re: Trim Plates For A Wayne 70 #61286
Sun Jun 25 2006 09:34 PM
Sun Jun 25 2006 09:34 PM
Joined: Jan 2003
Posts: 3,352
Kelowna British Columbia Canad...
D
dodogas Offline
Veteran Member
dodogas  Offline
Veteran Member
D
Joined: Jan 2003
Posts: 3,352
Kelowna British Columbia Canad...
Maybe we could make some??
Is it a spring clip with a pieced/tapped hole..cant really see the detail.

Cant look at my 3/4 wayne 70 (might be a Wayne52.5?) as mine has the early cast disintegrato trim..wish I could find some of that..
If there is a good demand I may be able to make some..

Re: Trim Plates For A Wayne 70 #61287
Mon Jun 26 2006 06:11 AM
Mon Jun 26 2006 06:11 AM
Joined: Nov 2004
Posts: 855
Baltimore, MD
C
chrisbowers Offline
Petro Enthusiast
chrisbowers  Offline
Petro Enthusiast
C
Joined: Nov 2004
Posts: 855
Baltimore, MD
I had the same problem, ended up fitting what was left of the clip into the hole and using Gorilla Glue to secure. Not the most professional method, but the stuff bonds like steel and it was impossible to notice from the outside (or even the inside for that matter).

Re: Trim Plates For A Wayne 70 #61288
Mon Jun 26 2006 02:39 PM
Mon Jun 26 2006 02:39 PM
Joined: Jan 2005
Posts: 2,702
Saline, Mi USA
B
blacktee Offline OP
Veteran Member
blacktee  Offline OP
Veteran Member
B
Joined: Jan 2005
Posts: 2,702
Saline, Mi USA
Okay !!! Thanks for the replys. Lance I think Dick would know best about this, But I believe they were crimped into the stainless steel trim pieces ? DB ?

Going to write Jim Potts now and ask where i can send him the hundred dollars. I've been on oldgas for awhile now, and feel i should give back. " What comes around goes around "

Thanks again everyone, Doug

Re: Trim Plates For A Wayne 70 #61289
Mon Jun 26 2006 05:11 PM
Mon Jun 26 2006 05:11 PM
Joined: Oct 2000
Posts: 22,780
Santa Paula, Calif
Dick Bennett Offline
Veteran Member
Dick Bennett  Offline
Veteran Member
Joined: Oct 2000
Posts: 22,780
Santa Paula, Calif
Dodo,
They can be made, but you'd have to make a gaZILLION to make any money for yor time. Plus for the average guy to take the time/effort to squish the little ears...JB Weld or Gorilla Glue works best/faster.

When the ity bity lug piece is missing, I have used JB to hold the outer frame to the door panel [4 little spots], insert glass & JB the inner frame in place [4 more little spots]. Faster than thoes ity bity machine screws.
They only hold the inner frame on that holds the face & adv. glass.
db

Re: Trim Plates For A Wayne 70 #61290
Mon Jun 26 2006 05:21 PM
Mon Jun 26 2006 05:21 PM
Joined: Nov 2005
Posts: 8,993
Antioch,IL
oldnfuelish Offline
Veteran Member
oldnfuelish  Offline
Veteran Member
Joined: Nov 2005
Posts: 8,993
Antioch,IL
WOW!!!! Doug !100 bucks,boy you just let us all know when we can help you any old time!!!! thats a great thing!!mick.let me know when your trying to put that add glass in!


Looking for gas,oil related clocks,especially neon and spinners .clock repair available. Mick
Re: Trim Plates For A Wayne 70 #61291
Mon Jun 26 2006 05:26 PM
Mon Jun 26 2006 05:26 PM
Joined: Jul 2000
Posts: 7,838
South of St. Louis, MO USA
Oldgas Offline
Moderator
Oldgas  Offline
Moderator
Joined: Jul 2000
Posts: 7,838
South of St. Louis, MO USA
Doug, I appreciate your generosity. Thanks!

But even more than that I love to see the community in action with members helping each other out. And without me begging anyone to do it. Most of you understand that everyone benefits when various solutions to problems are shared on this forum. We love to hear different methods and ideas. Plus, this topic will be available in the future as the next guy searches for "Wayne 70 trim" Cool.

------------------
Jim "Oldgas" Potts
Your host and moderator


Jim "Oldgas" Potts
Your host and moderator
Re: Trim Plates For A Wayne 70 #61292
Mon Jun 26 2006 05:45 PM
Mon Jun 26 2006 05:45 PM
Joined: Oct 2000
Posts: 22,780
Santa Paula, Calif
Dick Bennett Offline
Veteran Member
Dick Bennett  Offline
Veteran Member
Joined: Oct 2000
Posts: 22,780
Santa Paula, Calif
Doug,
Here is my address;
oldegaspump@....! LOL
Send it to Jim, so he can KEEP THIS SITE OPEN.
THANKS Jim

P.S. I don't know as much as you think I do !
EVERYONE MAKES MISTAKES, or YOUR NOT DOING ANYTHING. AND THAT IS YOUR MISTAKE.
db

Re: Trim Plates For A Wayne 70 #61293
Mon Jun 26 2006 06:14 PM
Mon Jun 26 2006 06:14 PM
Joined: Jan 2005
Posts: 2,702
Saline, Mi USA
B
blacktee Offline OP
Veteran Member
blacktee  Offline OP
Veteran Member
B
Joined: Jan 2005
Posts: 2,702
Saline, Mi USA
MR. POTTS I'M WAITING FOR A ADDRESS.

MR. BENNETT THANK YOU SIR !!!

DOC: IT WOULD BE SIMPLER JUST TO SEND YOU THE POST CARD ???

MICK: THANKS FOR EVERYTHING !!!

TELL YOUR FRIENDS/FAMILY / CO WORKERS YOU LOVE THEM.

DOUG



[This message has been edited by blackteetexacogold (edited 06-27-2006).]

Page 1 of 2 1 2

Moderated by  Oldgas, Ryan Underthun, Watchdog9 

Click for an eBay Search Form and lots more live petro auction listings

Copyright © 2018 Primarily Petroliana Interactive, All Rights Reserved

Powered by UBB.threads™ PHP Forum Software 7.6.1.1
(Release build 20180111)
Page Time: 0.026s Queries: 14 (0.005s) Memory: 1.9178 MB (Peak: 2.0667 MB) Zlib disabled. Server Time: 2018-06-21 10:46:19 UTC