Oldgas.com Home

Home | Help | Events | Books | Pictures | Auctions | Links | Collectors | Parts | Contact

Page 1 of 2 1 2 >
Topic Options
#61279 - Sun Jun 25 2006 07:02 PM Trim Plates For A Wayne 70
blacktee Offline
Veteran Member

Registered: Mon Jan 17 2005
Loc: Saline, Mi USA
Hey Guys:

I need some help here !!! I'm doing a Wayne 70. Working on the add glasses and face glasses. My parts list doesn't show the correct wording for these holders. Below are some pictures of the fastners. My question is ? Is there anyway to put them back in ? These go behind the stainless steel trim pieces. I have a bag full and want to keep this pump as original as possible. The guy that saves my *** here, will help me donate $100.00 to oldgas.com. I'm told they are made out of zinc ??

Give me some ideas guys !!!

Thanks, Doug






Top
Please use For Sale forums to sell

Please - NO offers to Buy or Sell in this forum category

Statements such as, "I'm thinking about selling this." are considered an offer to sell.
#61280 - Sun Jun 25 2006 07:08 PM Re: Trim Plates For A Wayne 70
Dick Bennett Offline
Veteran Member

Registered: Wed Oct 25 2000
Loc: Santa Paula, Calif
Sand lightly & JB WELD
db

------------------
**PUT A LID ON IT**
1qt RE-LIDDING
_________________________
Reproduction/Fantasy Cans
http://i124.photobucket.com/albums/p2/oldegaspump/AllCansMASTERTHUMBNAIL_zps4bfdbbc7.jpg
Rnd Can Re-lids


Top
#61281 - Sun Jun 25 2006 07:45 PM Re: Trim Plates For A Wayne 70
oldnfuelish Offline
FATW Feature Host

Registered: Wed Nov 02 2005
Loc: Antioch,IL
works great!did it to mine!
_________________________
Looking for gas,oil related clocks,especially neon and spinners .clock repair available. Mick

Top
#61282 - Sun Jun 25 2006 08:26 PM Re: Trim Plates For A Wayne 70
keithia Online   content
Veteran Member

Registered: Fri Dec 14 2001
Loc: USA
They are supposed to clip in but the clip part is normally broken or they fit so loose they fall back out and don't hold. Poor design in my book. JB Weld sounds good.

Keith
_________________________
Drive with Care and Buy Sinclair!! I buy Sinclair globes, signs, cans, ect.

Top
#61283 - Sun Jun 25 2006 08:55 PM Re: Trim Plates For A Wayne 70
Thunder II Offline
Veteran Member

Registered: Fri Jan 20 2006
Loc: On the plains of Colorado
JB Weld....
_________________________
Anything Chevron

I'd rather be flying.....

Top
#61284 - Sun Jun 25 2006 08:55 PM Re: Trim Plates For A Wayne 70
Ken Bird Offline
Petro Enthusiast

Registered: Wed Feb 15 2006
Loc: Carstairs, Alberta,formerly Sa...
Hi Fellas. When I did my 70, I didn't have any JB Weld handy, so I used some metal panel adhesive that we use in the autobody industry to "glue" on roof panels, door skins, etc. I know it's not that readily available to the general public, but it did work good. Just a little tid-bit that worked for me.
Ken.

Top
#61285 - Sun Jun 25 2006 11:24 PM Re: Trim Plates For A Wayne 70
gaspower Offline
Petro Enthusiast

Registered: Thu Mar 01 2001
Loc: Island County, Washington
JB Weld and don't forget to run a tap down and clean the threads.

Top
#61286 - Sun Jun 25 2006 11:34 PM Re: Trim Plates For A Wayne 70
dodogas Offline
Veteran Member

Registered: Sat Jan 25 2003
Loc: Kelowna British Columbia Canad...
Maybe we could make some??
Is it a spring clip with a pieced/tapped hole..cant really see the detail.

Cant look at my 3/4 wayne 70 (might be a Wayne52.5?) as mine has the early cast disintegrato trim..wish I could find some of that..
If there is a good demand I may be able to make some..

Top
#61287 - Mon Jun 26 2006 08:11 AM Re: Trim Plates For A Wayne 70
chrisbowers Offline
Petro Enthusiast

Registered: Mon Nov 22 2004
Loc: Baltimore, MD
I had the same problem, ended up fitting what was left of the clip into the hole and using Gorilla Glue to secure. Not the most professional method, but the stuff bonds like steel and it was impossible to notice from the outside (or even the inside for that matter).

Top
#61288 - Mon Jun 26 2006 04:39 PM Re: Trim Plates For A Wayne 70
blacktee Offline
Veteran Member

Registered: Mon Jan 17 2005
Loc: Saline, Mi USA
Okay !!! Thanks for the replys. Lance I think Dick would know best about this, But I believe they were crimped into the stainless steel trim pieces ? DB ?

Going to write Jim Potts now and ask where i can send him the hundred dollars. I've been on oldgas for awhile now, and feel i should give back. " What comes around goes around "

Thanks again everyone, Doug

Top
#61289 - Mon Jun 26 2006 07:11 PM Re: Trim Plates For A Wayne 70
Dick Bennett Offline
Veteran Member

Registered: Wed Oct 25 2000
Loc: Santa Paula, Calif
Dodo,
They can be made, but you'd have to make a gaZILLION to make any money for yor time. Plus for the average guy to take the time/effort to squish the little ears...JB Weld or Gorilla Glue works best/faster.

When the ity bity lug piece is missing, I have used JB to hold the outer frame to the door panel [4 little spots], insert glass & JB the inner frame in place [4 more little spots]. Faster than thoes ity bity machine screws.
They only hold the inner frame on that holds the face & adv. glass.
db
_________________________
Reproduction/Fantasy Cans
http://i124.photobucket.com/albums/p2/oldegaspump/AllCansMASTERTHUMBNAIL_zps4bfdbbc7.jpg
Rnd Can Re-lids


Top
#61290 - Mon Jun 26 2006 07:21 PM Re: Trim Plates For A Wayne 70
oldnfuelish Offline
FATW Feature Host

Registered: Wed Nov 02 2005
Loc: Antioch,IL
WOW!!!! Doug !100 bucks,boy you just let us all know when we can help you any old time!!!! thats a great thing!!mick.let me know when your trying to put that add glass in!
_________________________
Looking for gas,oil related clocks,especially neon and spinners .clock repair available. Mick

Top
#61291 - Mon Jun 26 2006 07:26 PM Re: Trim Plates For A Wayne 70
Oldgas Offline
Moderator

Registered: Tue Jul 25 2000
Loc: South of St. Louis, MO USA
Doug, I appreciate your generosity. Thanks!

But even more than that I love to see the community in action with members helping each other out. And without me begging anyone to do it. Most of you understand that everyone benefits when various solutions to problems are shared on this forum. We love to hear different methods and ideas. Plus, this topic will be available in the future as the next guy searches for "Wayne 70 trim" Cool.

------------------
Jim "Oldgas" Potts
Your host and moderator
_________________________
Jim "Oldgas" Potts
Your host and moderator

Top
#61292 - Mon Jun 26 2006 07:45 PM Re: Trim Plates For A Wayne 70
Dick Bennett Offline
Veteran Member

Registered: Wed Oct 25 2000
Loc: Santa Paula, Calif
Doug,
Here is my address;
oldegaspump@....! LOL
Send it to Jim, so he can KEEP THIS SITE OPEN.
THANKS Jim

P.S. I don't know as much as you think I do !
EVERYONE MAKES MISTAKES, or YOUR NOT DOING ANYTHING. AND THAT IS YOUR MISTAKE.
db
_________________________
Reproduction/Fantasy Cans
http://i124.photobucket.com/albums/p2/oldegaspump/AllCansMASTERTHUMBNAIL_zps4bfdbbc7.jpg
Rnd Can Re-lids


Top
#61293 - Mon Jun 26 2006 08:14 PM Re: Trim Plates For A Wayne 70
blacktee Offline
Veteran Member

Registered: Mon Jan 17 2005
Loc: Saline, Mi USA
MR. POTTS I'M WAITING FOR A ADDRESS.

MR. BENNETT THANK YOU SIR !!!

DOC: IT WOULD BE SIMPLER JUST TO SEND YOU THE POST CARD ???

MICK: THANKS FOR EVERYTHING !!!

TELL YOUR FRIENDS/FAMILY / CO WORKERS YOU LOVE THEM.

DOUG



[This message has been edited by blackteetexacogold (edited 06-27-2006).]

Top
Page 1 of 2 1 2 >

Moderator:  Oldgas, Ryan Underthun, Watchdog9 

Click on magnifying glass icon on lower left to search eBay

Copyright © 2017 Primarily Petroliana Interactive, All Rights Reserved