|
#621689
Mon Jul 13 2015 08:56 PM
|
Joined: Jul 2015
Posts: 13
Member
|
OP
Member
Joined: Jul 2015
Posts: 13 |
Newbie here .. looking for a 615 pump mechanism ? is this even possible? thnx
Last edited by 4Bigstuff; Mon Jul 13 2015 08:58 PM.
|
|
|
|
Joined: Jun 2013
Posts: 791 Likes: 5
Petro Enthusiast
|
Petro Enthusiast
Joined: Jun 2013
Posts: 791 Likes: 5 |
Go to www.gaspumps.us and send Tom Buckles an e-mail.
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
Yes its possible. Very common mechanism and they do turn up from time to time. Be patient and keep asking around. Tom is a good place to start!
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Jul 2015
Posts: 13
Member
|
OP
Member
Joined: Jul 2015
Posts: 13 |
|
|
|
|
Joined: Jul 2015
Posts: 13
Member
|
OP
Member
Joined: Jul 2015
Posts: 13 |
Thank you for your help! Have you ever installed the cylinder back in one of these ?
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
I have never had one apart, but others on this site have.
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Jul 2015
Posts: 13
Member
|
OP
Member
Joined: Jul 2015
Posts: 13 |
I'm sorry, have to be careful in my description. I was talking about the glass cylinder. I'm getting ready to reinstall and had questions ? Just use the cork gaskets ? no other caulk , etc? how tight do i want to tighten the jar lid down ? Just snug it ? its the original cylinder , i'm going to be scared to death. Thanks
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
OK--This is only my opinion and others may feel differently. I have done about 6 of these with 100% success. I use cork gaskets on top and bottom. I hand tighten all the nuts and when I finally use a wrench, I start tightening opposite nuts, about 1/2 turn at a time. I do this until I feel the torque load of the nuts is sufficient to hold the cylinder in place if the pump was jostled around, and then I leave it sit overnight. The next day I check all the nuts to see if any are loose, and I usually end up snugging all of them up a small amount. After a couple of days, I usually apply a silicone sealant to the gapped area around the base of the cylinder, and I leave the top alone. Seems to work just fine for me, but I'm sure others may do it differently?
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Dec 2011
Posts: 8,818 Likes: 2
Veteran Member
|
Veteran Member
Joined: Dec 2011
Posts: 8,818 Likes: 2 |
On all visibles, I use 1/4" thick, high density foam weatherstrip that has adhesive on one side. I cut it to width needed to fit the groove in the upper and lower housings. Then, I attach it to the housing. I don't use any caulking or silicone. I also tighten the nuts in a criss cross pattern. Just snug enough to hold everything in place.
Dave GILL, Dave's Garage & Memorabilia, Inc.
|
|
|
|
|
|