|
|
 Hanging double sided signs
|
Joined: Nov 2015
Posts: 161 Likes: 3
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Nov 2015
Posts: 161 Likes: 3 |
I've got 2 double sided porcelain signs roughly 25-28 inch diameter that I want to hang from building rafters so they are visible from both sides. Neither sign is in a ring. I'm to cheap lol and honestly one sign is a bit bent and wouldnt tolerate a ring anyways.
Neither sign has factory holes at the top to hang them up. Shy of drilling holes in the signs how can I hang these without rings??
Thanks guys!
Michael
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
Re: Hanging double sided signs
|
Joined: Sep 2007
Posts: 16,369 Likes: 675
Veteran Member
|
|
Veteran Member
Joined: Sep 2007
Posts: 16,369 Likes: 675 |
that sounds like a question with no answer, your either going to have to have Owen (lowright) make you some rings (reasonable) or drill depending on value of signs - please post picture of signs of subject to analyze .. ... 
RANDY
|
|
|
Re: Hanging double sided signs
|
Joined: Apr 2012
Posts: 360 Likes: 13
Petro Enthusiast
|
|
Petro Enthusiast
Joined: Apr 2012
Posts: 360 Likes: 13 |
I have always thought these might work, we use them to hold grid tight when installing ceilings, never have tried.
|
|
|
Re: Hanging double sided signs
|
Joined: Feb 2014
Posts: 2,879 Likes: 101
Veteran Member
|
|
Veteran Member
Joined: Feb 2014
Posts: 2,879 Likes: 101 |
Whatever you decide, make sure they don't slip out of whatever you decide to use. A sign from a rafter would probably end up in serious injury or worse.
-Steve B. (WTB: 48" Flying A button, 48" black/org Phillips 66, White Star, and Chevrolet Signs. Also looking for a Wayne 866. Send a PM. Thanks.)
|
|
|
Re: Hanging double sided signs
|
Joined: Aug 2011
Posts: 973 Likes: 21
Petro Enthusiast
|
|
Petro Enthusiast
Joined: Aug 2011
Posts: 973 Likes: 21 |
Have OWEN make rings I have two signs with bends in them NOT that hard to get in the rings then youre sure they wont come down
|
|
|
Re: Hanging double sided signs
|
Joined: May 2005
Posts: 4,595 Likes: 33
Veteran Member
|
Veteran Member
Joined: May 2005
Posts: 4,595 Likes: 33 |
Collecting Vintage Sunoco
|
|
|
Re: Hanging double sided signs
|
Joined: Sep 2007
Posts: 16,369 Likes: 675
Veteran Member
|
|
Veteran Member
Joined: Sep 2007
Posts: 16,369 Likes: 675 |
Ironworker - quality craftsmanship .. ... Name............ Owen Phone ..................1-502-396-3435
RANDY
|
|
|
Re: Hanging double sided signs
|
Joined: Nov 2015
Posts: 161 Likes: 3
Petro Enthusiast
|
|
OP
Petro Enthusiast
Joined: Nov 2015
Posts: 161 Likes: 3 |
Thanks guys for the replies!!
I had reached out to Owen a while back but once I realized one of the signs was warped or bent I backed off on the idea of rings figuring that would cause an issue. Plus I said I was cheap lol
I did wonder about some type of a clamp setup so appreciate that suggestion as well.
Michael
|
|
|
Re: Hanging double sided signs
|
Joined: Oct 2000
Posts: 1,667 Likes: 13
Veteran Member
|
|
Veteran Member
Joined: Oct 2000
Posts: 1,667 Likes: 13 |
I’ve seen some decent homemade rings. The one I remember that would be easy to make was just fairly thin flat stock bent in a circle and welded. They welded some little half moon tabs on one side of the inner ring. The others were just bolted in with small stove bolts. Would be fairly inexpensive to fabricate if you have time?
KJV Psalms 16:11
Thou wilt shew me the path of life:
in thy presence is fulness of joy;
at thy right hand there are pleasures for evermore.
|
|
|
Re: Hanging double sided signs
|
Joined: Jan 2012
Posts: 1,244 Likes: 48
Veteran Member
|
|
Veteran Member
Joined: Jan 2012
Posts: 1,244 Likes: 48 |
I’ve seen some decent homemade rings. The one I remember that would be easy to make was just fairly thin flat stock bent in a circle and welded. They welded some little half moon tabs on one side of the inner ring. The others were just bolted in with small stove bolts. Would be fairly inexpensive to fabricate if you have time? Yeah, I've made them too. It's do-able, but Owen is the master with these for sure. I'm not Mr. Safety be any means, but I'd want to make sure those signs are well mounted, a friction holder of some kind - No Bueno.
|
|
|
|
|
|
|
